Front License Plate Holder

[Porque No]

Has anyone found a front license plate holder that does not require drilling? Texas requires a front plate so looking for good options.

 

[TurboS]

Has anyone found a front license plate holder that does not require drilling? Texas requires a front plate so looking for good options.

@Cupholders has installed a lower bumper mounted front license plate shown here in his sweet looking photo.

 

[TurboS]

This thread here has several alternative options with the same mounting location, one of which is a quick removal for off-roading.

Bronco Raptor Spotted With Hideous Front License Plate Bracket

If you're anything like me, you already despise front license plates on vehicles. Thankfully, I currently live in a state that doesn't require a front license plate to be displayed, but I feel for everyone that lives in a state that does because the new Bronco front license plate location is...

www.broncoraptor.com

 

[onthelookout]

For my Badlands (modular front bumper), I purchased a bracket from HBTFD on Bronco6G. It’s pretty simple being bent sheet metal (similar to the picture above), but need to confirm it fits the Braptor bumper (didn’t try to install before sending to get PPF’d). Need to do more research though as I have seen ones that are centered on the skid plate but flip up while off-roading or have a quick release.

 

[DdYHrse]

I ordered a no drill holder off of Amazon that I plan to mount to the front skid plate. It was like $20. I am in Texas as well so I have to mount one up whenever they show up as well. I asked the dealer before it arrived to not drill the front the grill beforehand too.

 

[TurboS]

KR Off-Road License Plate Bracket is available from two of our sponsors​

4x4TruckLEDs.com @4x4TruckLEDs.com​

and​

Lethal Performance.com @LethalPerformance ​

​

 

[RileyBlizz]

Got this one I like it because it’s bent back a little bit very easy to install. Got it on valkyrieoffroad.com

 

[TurboS]

Got this one I like it because it’s bent back a little bit very easy to install. Got it on valkyrieoffroad.com

I agree, I like the sloping to the underside. Seems it would be less noticeable and better aero. Guessing the others could also be bent a little more to achieve a similar appearance,

 

[Orange Crush]

Front plate mount…

 

[SteelBronco]

To help any of those that may need to run a front license plate I used the DV8 bracket which clearly states on their website "excludes: Bronco Raptor".
If you don't mind buying the following you can use it without a problem.
https://www.boltdepot.com/Product-Details.aspx?product=13785 Need 2
https://www.boltdepot.com/Product-Details.aspx?product=18972 Need 2
https://www.boltdepot.com/Product-Details.aspx?product=22030 Need 6
When all done it's a very strong bracket!
Hope this might help someone.
(Yes, I need to clean the shop floor haha!)

 

[TurboS]

To help any of those that may need to run a front license plate I used the DV8 bracket which clearly states on their website "excludes: Bronco Raptor".
If you don't mind buying the following you can use it without a problem.
https://www.boltdepot.com/Product-Details.aspx?product=13785 Need 2
https://www.boltdepot.com/Product-Details.aspx?product=18972 Need 2
https://www.boltdepot.com/Product-Details.aspx?product=22030 Need 6
When all done it's a very strong bracket!
Hope this might help someone.
(Yes, I need to clean the shop floor haha!)

View attachment 7224

View attachment 7225

View attachment 7226

View attachment 7227

Very Well done! I really like the position with the top edge just below the silver intercooler inlet and the slope!

 

[braptor0074]

To help any of those that may need to run a front license plate I used the DV8 bracket which clearly states on their website "excludes: Bronco Raptor".
If you don't mind buying the following you can use it without a problem.
https://www.boltdepot.com/Product-Details.aspx?product=13785 Need 2
https://www.boltdepot.com/Product-Details.aspx?product=18972 Need 2
https://www.boltdepot.com/Product-Details.aspx?product=22030 Need 6
When all done it's a very strong bracket!
Hope this might help someone.
(Yes, I need to clean the shop floor haha!)

View attachment 7224

View attachment 7225

View attachment 7226

View attachment 7227

Quick question, how’d you get the mini brush bar to fit with that trim piece between the bumper and the grill?

 

[SteelBronco]

Quick question, how’d you get the mini brush bar to fit with that trim piece between the bumper and the grill?

Contur back edges with a grinder and smooth with a file. Paint
This will have some interference in the front camera. It is not bad at all you still easily see above and below it.
(Hint: make cardboard cutout for both sides to make it easier)

https://www.stickerfab.com/collections/2021-ford-bronco/products/21-offroad-mini-bull-bar-2021-bronco

 

[timhutch]

I had my local dealer/custom shop make up a holder for the front license plate. They did it in two days (powder coating and all) and I thought it came out great. It doesn't block anything, isn't at risk if I get into a rock with my front skid plate and it used two existing bolts on the top of the bumper (no drilling anything). Very happy!

 

[TurboS]

I had my local dealer/custom shop make up a holder for the front license plate. They did it in two days (powder coating and all) and I thought it came out great. It doesn't block anything, isn't at risk if I get into a rock with my front skid plate and it used two existing bolts on the top of the bumper (no drilling anything). Very happy!View attachment 8265

Welcome to the Forum! 🍻 Well thought out and I love that the mounting can be removed without trace.

 

[Cr8r78]

To help any of those that may need to run a front license plate I used the DV8 bracket which clearly states on their website "excludes: Bronco Raptor".
If you don't mind buying the following you can use it without a problem.
https://www.boltdepot.com/Product-Details.aspx?product=13785 Need 2
https://www.boltdepot.com/Product-Details.aspx?product=18972 Need 2
https://www.boltdepot.com/Product-Details.aspx?product=22030 Need 6
When all done it's a very strong bracket!
Hope this might help someone.
(Yes, I need to clean the shop floor haha!)

View attachment 7224

View attachment 7225

View attachment 7226

View attachment 7227

Why 6 washers?? Thank you!

 

[Porque No]

I found one that works great and is easily removed when you are off road. Sto N Sho quick release bracket. No drilling, it uses current bolts on bumper of Raptor.

 

[DdYHrse]

Looks good. I just said screw it and let the plate line up with the natural slant of the skid plate and didn't slant it forward. I do like the spacer idea though. I have driven by enough police officers and they haven't said anything, but if they do I will definitely be using that idea. Still wish I didn't have to have one up front at all though.

 

[SteelBronco]

Why 6 washers?? Thank you!

If I remember correctly I used one on each side of the nylon spacer and then one for the attaching bolt per side. I realize the pictures don't show them this way but this is how I ended up in the final version.

 

[Johnny Mo]

Another vote for the DV8 with similar spacers and longer bolts.